1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Jrobz23's Recent Activity

  1. Jrobz23 replied to the thread Tq Is Fun.

    This little motor is sweet. That being said until the Roxor community gets things stripped down to mechanical, the Kubota is a good bet...

    Jun 17, 2019 at 9:23 PM
  2. Jrobz23 replied to the thread Axle Assemblies.

    Both my Roxor and '57 seem about 28" (prolly give/take a half inch) spring center to center. I'm not seeing much to stop this swap...

    Jun 17, 2019 at 9:16 PM
  3. Jrobz23 replied to the thread Drive Train Length?.

    OK by foot I guess I was optimistic. It's more like 6" ish. Still that is significant for above the cross-member space. This way you can...

    Jun 17, 2019 at 9:02 PM
  4. Jrobz23 liked Buildflycrash's post in the thread Roxor - Seat Install.

    It actually does clear. I’m going to try to lower the passenger seat by a couple inches in the coming weeks. Stay tuned.

    Jun 17, 2019 at 8:49 PM
  5. Jrobz23 replied to the thread Drive Train Length?.

    I don't think it's THAT much longer than the beefcake 4 spd's people put in + adapt to the Spicer18. I have a later grill sitting in...

    Jun 17, 2019 at 4:41 PM
  6. Jrobz23 replied to the thread Roxor Transfer Case.

    No word yet that I see. It'd be slick if ATV made an under-drive unit that goes where the PTO does. It'd be a sweet 'doubler' kinda...

    Jun 16, 2019 at 10:53 PM
  7. Jrobz23 replied to the thread Drive Train Length?.

    It's pretty long. It's like AX15 big. If people have gotten one of those in an early, this'd work. Maybe if you swap to a later grill...

    Jun 16, 2019 at 10:49 PM
  8. Jrobz23 replied to the thread Axle Assemblies.

    I'll have to get some closer measurements this week.

    Jun 16, 2019 at 10:45 PM
  9. Jrobz23 replied to the thread Roxor - Seat Install.

    I bet not. It's a full high back seat.

    Jun 16, 2019 at 10:44 PM
  10. Jrobz23 replied to the thread Roxor Parts Swaps.

    Their MDI line all had VEs, which is what this engine derives from. In the US, some of their tractors had the same engine, in VE.

    Jun 16, 2019 at 10:43 PM
  11. Jrobz23 replied to the thread Tq Is Fun.

    I got the decals on this weekend: [IMG]

    Jun 16, 2019 at 10:37 PM
  12. Jrobz23 replied to the thread Roxor Parts Swaps.

    By all the digging and eye ball calculous I’ve performed, a 3 bolt VE pump should just bolt up. The CR system on this engine is an...

    Jun 16, 2019 at 2:25 PM
  13. Jrobz23 replied to the thread Roxor Parts Swaps.

    Nothing material yet. I need some parts in my hands.

    Jun 16, 2019 at 12:07 PM
  14. Jrobz23 replied to the thread Axle Assemblies.

    Full float rear kits. I’m pretty sure most fronts are already full float.

    Jun 15, 2019 at 10:13 PM
  15. Jrobz23 replied to the thread Axle Assemblies.

    I haven't seen anyone use one yet. To the OP, OnTheRoxFab has RCV 30 spline axles and a couple people have full float 30 spline kits...

    Jun 15, 2019 at 9:19 PM
New Posts