1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

F134 Draft Tube

Discussion in 'Early CJ5 and CJ6 Tech' started by DanStew, Dec 28, 2023.

  1. Dec 28, 2023
    DanStew

    DanStew Preowned Merkin salesman Staff Member

    Lexington, South...
    Joined:
    Sep 22, 2002
    Messages:
    4,585
    Well now that the Jeep is up and running and i am trying to mediate the leaks here and there. An annoying one that is happening is the Draft tube on the side valve cover. The oil is dripping from the tube down the oil pump bulge and onto the floor. I am going to eventually go to a PCV setup but can i just angle the draft tube up to stop this or will it cause another issue? Right now it is below being parallel to the ground and it is just dripping. Will it just drain back into the engine if it gets angled up a bit?
     
    DanStew, Dec 28, 2023
    #1
    Glenn and Ol Fogie like this.
  2. Dec 28, 2023
    PeteL

    PeteL If it wasn't for physics, and law enforcement... 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Hills of NH
    Joined:
    Aug 3, 2003
    Messages:
    9,825
    Would that not also carry dust and grit particles? Perhaps an add-on air filter would be needed, such as Harleys and hot rods sometimes use.
     
    PeteL, Dec 28, 2023
    #2
    Glenn likes this.
  3. Dec 28, 2023
    DanStew

    DanStew Preowned Merkin salesman Staff Member

    Lexington, South...
    Joined:
    Sep 22, 2002
    Messages:
    4,585
    That would be a problem. I guess to buy the PCV system soon.
     
    DanStew, Dec 28, 2023
    #3
    Glenn and Dwins1 like this.
  4. Dec 28, 2023
    Jw60

    Jw60 Cool school 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Sedalia MO.
    Joined:
    Apr 8, 2008
    Messages:
    4,819
    Catch can, or diaper.
     
    Jw60, Dec 28, 2023
    #4
    Rick Whitson and Glenn like this.
  5. Dec 28, 2023
    Dwins1

    Dwins1 Member

    Port Richey, Florida
    Joined:
    Jun 20, 2022
    Messages:
    296
    That’s what I was going to say. Just get the parts and do it right….
     
    Dwins1, Dec 28, 2023
    #5
    Glenn likes this.
  6. Dec 28, 2023
    duffer

    duffer Rodent Power

    Bozeman, MT
    Joined:
    Sep 17, 2009
    Messages:
    4,514
    Yep. I suspect there are a lot of complete, used systems floating around in various members' parts stashes here. Put a WTB in the classified.
     
    duffer, Dec 28, 2023
    #6
    Glenn likes this.
  7. Dec 28, 2023
    Oldpappy

    Oldpappy A.C. Fults - Curmudgeon at large 2022 Sponsor

    East Tennessee
    Joined:
    Feb 8, 2021
    Messages:
    1,668
    Maybe there is some crud in the valve gallery clogging the oil return ports, or the cone screen may be missing. Oil shouldn't build up in there enough to run out the draft tube.

    You would be better off to install the proper PCV system, but if the oil return ports are plugged the PCV system might start sucking in oil.
     
    Oldpappy, Dec 28, 2023
    #7
    Dwins1, DanStew and Glenn like this.
New Posts