1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

71 Wheeling Rig

Discussion in 'Builds and Fabricators Forum' started by Fireball, Jan 18, 2021.

Page 49 of 49
  1. Apr 30, 2024
    Fireball

    Fireball Well-Known Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Pullman, WA
    Joined:
    Feb 9, 2018
    Messages:
    5,768
    If I use your plates, I need to fabricate shock mounts. Probably upper and lower. Outside the scope of this current round of work. I do like the plates though.
     
    Fireball, Apr 30, 2024
    #961
    Jw60 likes this.
  2. Apr 30, 2024
    Fireball

    Fireball Well-Known Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Pullman, WA
    Joined:
    Feb 9, 2018
    Messages:
    5,768
    I used U-bolts Direct: https://www.uboltsdirect.com/

    Haven't used them before, I just did a web search and they had a decent price for bolts+shipping. The quality seems fantastic.
     
    Fireball, Apr 30, 2024
    #962
    blalp!, WTn800 and givemethewillys like this.
  3. Apr 30, 2024
    timsresort

    timsresort Active Member 2023 Sponsor 2022 Sponsor

    South Lake Tahoe CA
    Joined:
    Jan 22, 2014
    Messages:
    1,419
    That could almost make a guy want to light one up...
     
    timsresort, Apr 30, 2024
    #963
    givemethewillys, Cj5dale, Fireball and 1 other person like this.
  4. Apr 30, 2024
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,703
    I am in the same boat....thinking I might be able to weld lower shock mount onto the plate similar to OEM, but it will loose some travel, but maybe not enough to matter?....if shock length gets too short, that probably means the taller ford style upper mount. In any case, figured I'd never get another chance to get some these for reasonable price, so ordered them and they can sit on the shelf until I am ready to figure it out.
     
    FinoCJ, Apr 30, 2024
    #964
    blalp! and Fireball like this.
  5. Apr 30, 2024
    Fireball

    Fireball Well-Known Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Pullman, WA
    Joined:
    Feb 9, 2018
    Messages:
    5,768
    My problem is that once I start needing to do fab work, I might as well go with YJ springs.

    Scope creep at its finest.
     
    Fireball, Apr 30, 2024
    #965
    blalp!, 3b a runnin, colojeepguy and 1 other person like this.
  6. Apr 30, 2024
    Jw60

    Jw60 That guy 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Sedalia MO.
    Joined:
    Apr 8, 2008
    Messages:
    4,880
    I'm lucky that my shocks are already too short and holding the drop short. For the front all I need to do is trim the outside flange shorter and weld some round stock with Cotter pin holes onto the outside flange.

    If my shock length were good I would drill the upper shock bracket rivets and shim it up with 3/4" bar stock or tube with internal crush sleeves.
     
    Jw60, Apr 30, 2024
    #966
    blalp! and Fireball like this.
  7. May 2, 2024
    FinoCJ

    FinoCJ 1970 CJ5 Staff Member

    Bozeman, MT
    Joined:
    Jul 18, 2013
    Messages:
    5,703
    Not that it avoids fab work, but I am much more interested in shackle reversal with 1.75 springs than anything yj.
     
    FinoCJ, May 2, 2024
    #967
    Fireball likes this.
Page 49 of 49
New Posts