1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 8
  1. Heimbig2
    Post

    1974 Dana 44 Warn Full Floating Rear Axle Kit

    Fireball- do you know if the Yukon Gear YHC 50002 drive flange kit would work with this setup? Mike
    Post by: Heimbig2, Jan 26, 2021 at 4:35 PM in forum: Intermediate CJ-5/6/7/8
  2. Heimbig2
    Post

    1974 Dana 44 Warn Full Floating Rear Axle Kit

    Here are some photos [ATTACH] [ATTACH] [ATTACH] [ATTACH]
    Post by: Heimbig2, Jan 25, 2021 at 8:58 PM in forum: Intermediate CJ-5/6/7/8
  3. Heimbig2
    Post

    1974 Dana 44 Warn Full Floating Rear Axle Kit

    I could post a photos but I just talked with Warn and they said those were custom made for this application
    Post by: Heimbig2, Jan 25, 2021 at 2:21 PM in forum: Intermediate CJ-5/6/7/8
  4. Heimbig2
    Thread

    1974 Dana 44 Warn Full Floating Rear Axle Kit

    I was looking at picking up a used full floating rear axle kit for a 1974 Dana 44 CJ5 axle. The problem is one of the wheel hubs is bent beyond...
    Thread by: Heimbig2, Jan 25, 2021 at 12:57 AM, 8 replies, in forum: Intermediate CJ-5/6/7/8
  5. Heimbig2
    Post

    Holbrook Springs Instructions

    Right- I just got a set from Benz Spring and there was a problem with the bushings in the eye. There is a short end of the spring, which is the...
    Post by: Heimbig2, Jan 12, 2021 in forum: Flat Fender Tech
  6. Heimbig2
    Post

    Holbrook Springs Instructions

    So just like in the instructions above, you can see the center bolt is offset towards the outboard or bumper side and that would have the shackles...
    Post by: Heimbig2, Jan 11, 2021 in forum: Flat Fender Tech
  7. Heimbig2
    Post

    Holbrook Springs Instructions

    For anybody that is running Holbrook springs I have a question. I am working with Benz springs on a set however they sent me a set that are the...
    Post by: Heimbig2, Jan 11, 2021 in forum: Flat Fender Tech
  8. Heimbig2
    Post

    Spring Hanger Bolts

    These are Crown Automotive and are 3 1/4 inches long. Regular bolts would lose the ability to grease them for the bronze bushing.
    Post by: Heimbig2, Jan 11, 2021 in forum: Flat Fender Tech
  9. Heimbig2
    Post

    Spring Hanger Bolts

    do you know of a source for the correct bolts?
    Post by: Heimbig2, Jan 10, 2021 in forum: Flat Fender Tech
  10. Heimbig2
    Thread

    Spring Hanger Bolts

    I am putting on new leaf springs on my CJ3B , they are 1.75 inches wide. I bought new pivot bolts but the are a little longer than stock. It...
    Thread by: Heimbig2, Jan 9, 2021, 10 replies, in forum: Flat Fender Tech
  11. Heimbig2
    Post

    Holbrook Springs Instructions

    I am picking up a set from Benz Spring Co in Oregon next week. It is there model HJS-3F and HJS-3R they retail for about $200 a spring. You will...
    Post by: Heimbig2, Dec 17, 2020 in forum: Flat Fender Tech
  12. Heimbig2
    Post

    Setting Pinion Depth On 74 Cj5 Dana 44 Rear End

    Do I need a set up bearing for the outer Pinion bearing (nearest the yoke) or does that bearing slide on without being pressed on? Mike
    Post by: Heimbig2, Dec 8, 2020 in forum: Intermediate CJ-5/6/7/8
  13. Heimbig2
    Thread

    Setting Pinion Depth On 74 Cj5 Dana 44 Rear End

    I bought an empty dana 44 housing that I will be putting 4.56 gears into. The inner pinion bearing race was still in place and I removed it an it...
    Thread by: Heimbig2, Dec 6, 2020, 4 replies, in forum: Intermediate CJ-5/6/7/8
  14. Heimbig2
    Post

    15x12 Wheels

    Just for fun not DOT approved
    Post by: Heimbig2, Dec 2, 2020 in forum: Intermediate CJ-5/6/7/8
  15. Heimbig2
    Post

    15x12 Wheels

    those are the exact ones
    Post by: Heimbig2, Dec 1, 2020 in forum: Intermediate CJ-5/6/7/8
  16. Heimbig2
    Post

    15x12 Wheels

    I will be running 33x15.50x15 tires
    Post by: Heimbig2, Dec 1, 2020 in forum: Intermediate CJ-5/6/7/8
  17. Heimbig2
    Post

    15x12 Wheels

    Thanks, as for the Mickey Thompson Classic III, if you check their website it says they will not fit over the hubs on a CJ5, the bore is too small.
    Post by: Heimbig2, Nov 30, 2020 in forum: Intermediate CJ-5/6/7/8
  18. Heimbig2
    Thread

    15x12 Wheels

    Does anyone know if anyone still makes 15-12 inch wheels for a Jeep CJ, prefer aluminum.
    Thread by: Heimbig2, Nov 29, 2020, 10 replies, in forum: Intermediate CJ-5/6/7/8
  19. Heimbig2
    Post

    4 Inch Lift Springs On Cj3b

    Yes they are military wrapped and flat center made by Warn.
    Post by: Heimbig2, Oct 30, 2020 in forum: Flat Fender Tech
  20. Heimbig2
    Thread

    Which Model Rancho Shocks

    For those that are running Holbrook suspension in their flatties which model number shocks are you running?
    Thread by: Heimbig2, Oct 28, 2020, 1 replies, in forum: Flat Fender Tech
Showing results 1 to 20 of 144 Next >
Search Again
Page 1 of 8
New Posts