1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 2
  1. jjfalconer
    Post

    Wiring help for 75 CJ5

    There is no HOT wire going to the horn. All the horn does is complete a ground and the horn MUST be run though a Relay.
    Post by: jjfalconer, Feb 28, 2005 in forum: Intermediate CJ-5/6/7/8
  2. jjfalconer
    Post

    GM HEI gear spacer?

    When i did this I did not use a spacer and it works really good. If you have to much play in the saft then use a spacer but if it looks good...
    Post by: jjfalconer, Jan 11, 2005 in forum: Intermediate CJ-5/6/7/8
  3. jjfalconer
    Post

    Column Bearing

    I recieved this bushing today and it fits really good. I have not finished installing the column yet becuase I need to get some grease before i...
    Post by: jjfalconer, Sep 27, 2004 in forum: Intermediate CJ-5/6/7/8
  4. jjfalconer
    Post

    Column Bearing

    Thank you for making the replacement bushing for me. I have not recieved it yet but if It comes in today I will try it and let you know what...
    Post by: jjfalconer, Sep 27, 2004 in forum: Intermediate CJ-5/6/7/8
  5. jjfalconer
    Post

    Column Bearing

    I do not check the board very often becuase I'm work two jobs and do not get home until 8 or 9 at night. By the time I make something to eat I'm...
    Post by: jjfalconer, Sep 24, 2004 in forum: Intermediate CJ-5/6/7/8
  6. jjfalconer
    Post

    Column Bearing

    Mcruff Will you make a new bushing for me if I get the measurements from this jeep. The one you made did not fit. I would like to get this...
    Post by: jjfalconer, Sep 13, 2004 in forum: Intermediate CJ-5/6/7/8
  7. jjfalconer
    Post

    Column Bearing

    I have tried this bushing and it did not fit. I will see if I can get some measurements off my old bushing. I have been thinking about...
    Post by: jjfalconer, Sep 1, 2004 in forum: Intermediate CJ-5/6/7/8
  8. jjfalconer
    Post

    Column Bearing

    I have the bushing but I have not had a chance to try it yet. I should have a chance this weekend though.
    Post by: jjfalconer, Aug 11, 2004 in forum: Intermediate CJ-5/6/7/8
  9. jjfalconer
    Post

    lift need advice .... want to fit 35's

    Get rid of the body lift. Install 4 inch lift (this setup clears 33 with out a problem and looks like it will clear 35's). If you have problems...
    Post by: jjfalconer, Jul 12, 2004 in forum: Intermediate CJ-5/6/7/8
  10. jjfalconer
    Post

    '74 V8 Alternator & Regulator Wiring

    Go with the chevy one, Cheaper to replace, simple to wire, parts are easy to get, any Auto Parts store will have one. If you want to wire the...
    Post by: jjfalconer, Jul 7, 2004 in forum: Intermediate CJ-5/6/7/8
  11. jjfalconer
    Post

    Column Bearing

    I PM'ed you
    Post by: jjfalconer, Jul 6, 2004 in forum: Intermediate CJ-5/6/7/8
  12. jjfalconer
    Post

    Column Bearing

    I do not know of a local shop that can make this for me. Would someone be willing to have one made and I will send you the money plus shipping to...
    Post by: jjfalconer, Jul 6, 2004 in forum: Intermediate CJ-5/6/7/8
  13. jjfalconer
    Post

    Radiator Question

    Just bring your current radiator to a radiator shop and have them change the side the lower hose is on. While you are at it have them clean the...
    Post by: jjfalconer, Jul 2, 2004 in forum: Early CJ5 and CJ6 Tech
  14. jjfalconer
    Post

    Thick starter cable melting!

    If it was Trans related it would turn over hard with the plugs removed. Have you tried to turn the motor with a wrench by hand to make sure it...
    Post by: jjfalconer, Jun 28, 2004 in forum: Early CJ5 and CJ6 Tech
  15. jjfalconer
    Post

    Thick starter cable melting!

    The strater should not get hot with the key "ON". There is no power going to the starter with the key in "ON". Only time there is power to the...
    Post by: jjfalconer, Jun 25, 2004 in forum: Early CJ5 and CJ6 Tech
  16. jjfalconer
    Post

    Column Bearing

    Yes it is where the shaft attaches to the bottom end of the colunm. The bearing is in the colunm it self though and not part of the shaft.
    Post by: jjfalconer, Jun 22, 2004 in forum: Intermediate CJ-5/6/7/8
  17. jjfalconer
    Thread

    Column Bearing

    Hi, Does anyone know where I can get the lower Bearing that goes to the streering Column on a 1974 CJ5. My streering Column has alot of...
    Thread by: jjfalconer, Jun 21, 2004, 31 replies, in forum: Intermediate CJ-5/6/7/8
  18. jjfalconer
    Post

    CJ-5 Vin Numbers

    This is some infomation I found on Jeep Vin numbers that may help. http://mysite.verizon.net/jandjfalconer/JeepVinInfo.htm
    Post by: jjfalconer, Apr 10, 2004 in forum: Early CJ5 and CJ6 Tech
  19. jjfalconer
    Post

    CJ-5 Vin Numbers

    I will try to extend this out for more years. I need to find as much info as I can for jep vin numbers. Any one have sources for Vin Number Info?
    Post by: jjfalconer, Apr 10, 2004 in forum: Early CJ5 and CJ6 Tech
  20. jjfalconer
    Post

    CJ-5 Vin Numbers

    To the best of my knowage this is right. I have spent many hours researching this online. I have found pages with orginal jeep docs images that...
    Post by: jjfalconer, Apr 9, 2004 in forum: Early CJ5 and CJ6 Tech
Showing results 1 to 20 of 23 Next >
Search Again
Page 1 of 2
New Posts