1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Search Results

Search Again
Page 1 of 8
  1. rsbad454
    Post

    My 75 CJ-5

    Yeah, I still have to fix TF727 pan leak and I think the freeze plug leaks.
    Post by: rsbad454, Aug 25, 2015 in forum: Builds and Fabricators Forum
  2. rsbad454
    Post

    Radiator Clips

    I found some U Nuts at tractor Supply or Ace I think.
    Post by: rsbad454, Aug 25, 2015 in forum: Intermediate CJ-5/6/7/8
  3. rsbad454
    Post

    My 75 CJ-5

    Thanks, I learned a lot working on this old beast. ...main thing is the money....lol
    Post by: rsbad454, Aug 25, 2015 in forum: Builds and Fabricators Forum
  4. rsbad454
    Post

    Renegade rescue/ Bill and Techs excellent adventure

    Nice project.... :)
    Post by: rsbad454, Aug 24, 2015 in forum: Builds and Fabricators Forum
  5. rsbad454
    Post

    My 75 CJ-5

    It's been a while, but I got it running...had a some issues during assembly that I overlooked, but have since remedied them. Now I'm just driving...
    Post by: rsbad454, Aug 23, 2015 in forum: Builds and Fabricators Forum
  6. rsbad454
    Post

    Rebuilt engine no compression

    Yeah, I'll try the lazy way first....and use drill motor. I figured it would have primed from the oil that was still in filter, but I guess not.
    Post by: rsbad454, Jul 25, 2015 in forum: Intermediate CJ-5/6/7/8
  7. rsbad454
    Post

    Rebuilt engine no compression

    Got it fired up, wasn't getting oil pressure after a minute or two so. I think I either need to pack pump with vasaline again or pull distributor...
    Post by: rsbad454, Jul 24, 2015 in forum: Intermediate CJ-5/6/7/8
  8. rsbad454
    Post

    Radiator Clips

    I looked at some of the U nuts from O Reilly and they are a different style.
    Post by: rsbad454, Jul 16, 2015 in forum: Intermediate CJ-5/6/7/8
  9. rsbad454
    Post

    Radiator Clips

    I'll check local hardware, wasn't sure if these were still around.
    Post by: rsbad454, Jul 12, 2015 in forum: Intermediate CJ-5/6/7/8
  10. rsbad454
    Post

    Radiator Clips

    Just the clips would work....
    Post by: rsbad454, Jul 10, 2015 in forum: Intermediate CJ-5/6/7/8
  11. rsbad454
    Thread

    Radiator Clips

    Does anyone know where I can find the clips that snap onto radiator support? Clips for the screws that secure shroud and radiator to...
    Thread by: rsbad454, Jul 10, 2015, 13 replies, in forum: Intermediate CJ-5/6/7/8
  12. rsbad454
    Post

    Rebuilt engine no compression

    Not a resurrected thread, just on going. I wasn't able to get the engine started so Jeep sat for over a year until I had time recently to look at...
    Post by: rsbad454, Jul 9, 2015 in forum: Intermediate CJ-5/6/7/8
  13. rsbad454
    Post

    Rebuilt engine no compression

    I always paint the lifter valleys and typically the rocker area of the heads. Basically fills in the pores and voids in the casting to lessen the...
    Post by: rsbad454, Jul 6, 2015 in forum: Intermediate CJ-5/6/7/8
  14. rsbad454
    Post

    Rebuilt engine no compression

    Well, I should have the timing correct now...I also had to take each lifter out and drain the oil out. I couldn't preload the lifters because they...
    Post by: rsbad454, Jul 6, 2015 in forum: Intermediate CJ-5/6/7/8
  15. rsbad454
    Post

    Rebuilt engine no compression

    Well, pulled engine and found that I screwed up as suspected and installed bottom sprocket on wrong key way, thus not having upper sprocket...
    Post by: rsbad454, Jun 14, 2015 in forum: Intermediate CJ-5/6/7/8
  16. rsbad454
    Post

    Rebuilt engine no compression

    Well, I'm just going to pull engine back out and pull timing cover. I have been breaking rocker pedestals and now bent a couple of pushrod. I used...
    Post by: rsbad454, Feb 19, 2015 in forum: Intermediate CJ-5/6/7/8
  17. rsbad454
    Post

    Rebuilt engine no compression

    These time pretty much the same as a chevy. This isn't a distributor being 180 out issue, this is an actual valve timing event issue. I just need...
    Post by: rsbad454, Jan 24, 2014 in forum: Intermediate CJ-5/6/7/8
  18. rsbad454
    Post

    1973 CJ 5 Trail Rig

    Yup, these Jeeps take your cash.....lol
    Post by: rsbad454, Jan 23, 2014 in forum: Builds and Fabricators Forum
  19. rsbad454
    Post

    Rebuilt engine no compression

    I haven't posted in a while, but will hopefully have a chance to tear timing cover off engine and double check the cam to crank timing comib g up.
    Post by: rsbad454, Jan 23, 2014 in forum: Intermediate CJ-5/6/7/8
  20. rsbad454
    Post

    Rebuilt engine no compression

    I either mistyped or you misread....My cloyes crank sprocket has three slots cut into it. One for advance, zero and retard...I lined slot on crank...
    Post by: rsbad454, Sep 22, 2013 in forum: Intermediate CJ-5/6/7/8
Showing results 1 to 20 of 145 Next >
Search Again
Page 1 of 8
New Posts