1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Electrical Question

Discussion in 'Early CJ5 and CJ6 Tech' started by linckeil, Mar 27, 2006.

  1. Mar 27, 2006
    linckeil

    linckeil Member

    Danbury CT
    Joined:
    Aug 19, 2004
    Messages:
    492
    I have a heater fan motor with relay from a 1991 Chevy Blazer that I'm going to stuff into my stock jeep heater box. The stock jeep fan motor has a high and low speed, but the blazer motor is a single speed.

    It would be a peice of cake to wire it as a single high speed, but I'd like to have at least a high and low setting. Obviously this is possible as the Blazer had a 4 speed setting. My question is, How? Is there some kind of switch I can wire in that would provide differing resistences when set to different speeds? Any websites or books out there that someone can direct me to?

    Thanks.
     
    linckeil, Mar 27, 2006
    #1
  2. Mar 27, 2006
    jd7

    jd7 Sponsor

    Nacogdoches,Texas
    Joined:
    Mar 30, 2004
    Messages:
    1,745
    Napa used to list several types like that in their books
     
    jd7, Mar 27, 2006
    #2
  3. Mar 28, 2006
    AKCJ

    AKCJ Active Member

    Fairbanks, Alaska
    Joined:
    Aug 12, 2003
    Messages:
    1,035
    Yes. I got a two speed pull switch from NAPA and it had the built in resister for low speed. It even has a built in fuse. And it was low $!
     
    AKCJ, Mar 28, 2006
    #3
  4. Mar 28, 2006
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    Resistors dissipate a lot of heat ... I would use an SCR and turn it on and off at different rates to get a change in voltage. However, I'm fairly proficient with electronics stuff...
     
    timgr, Mar 28, 2006
    #4
  5. Mar 28, 2006
    jpflat2a

    jpflat2a what's that noise?

    Hermosa, SD
    Joined:
    Jul 30, 2003
    Messages:
    8,521
    which is why the factory resistor pack is mounted thru the housing; when fan is on, air blows onto the resistors....
     
    jpflat2a, Mar 28, 2006
    #5
  6. Mar 28, 2006
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,118

    O.K., I'll bite- Assuming we're operating @ 12V DC once you turn the SCR on, How are we turning it Off again ??? :)

    Enquiring Minds Want To Know-

    H.

    p.s. What kinda filter are we using to keep da hash outta da HI FI ?
     
    Howard Eisenhauer, Mar 28, 2006
    #6
  7. Mar 29, 2006
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    I'd charge a capacitor for the timing (RC circuit). There are lots of ways to generate a square wave at a specific frequency. Simplest I can think of is a flip-flop that alternately charges/decharges the cap. Model train controllers use this kind of a circuit to start locomotives slowly.

    Re the rf interference, put it in a box and use a Corcom-style line filter on the outputs.

    Not complicated in toto, but putting the resistors in the air flow (per Jim's post) would be simpler and cheaper.
     
    timgr, Mar 29, 2006
    #7
  8. Mar 30, 2006
    65CJ5

    65CJ5 Member

    Albuquerque
    Joined:
    Sep 22, 2002
    Messages:
    156
    I have some info on my site that might help you:

    http://home.comcast.net/~sday77/binky/index.htm

    Go to the repair section and look at the heater motor stuff. I used some big ceramic resistors that worked OK. SCR would be neat. Anyone have a schematic for that?

    Stan
     
    65CJ5, Mar 30, 2006
    #8
  9. Mar 30, 2006
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    I don't have a schematic, but one source on the web suggested a speed control from a junked cordless drill. That's an SCR circuit. Other than that, I'd hit the books and look for a DC motor control circuit that I could adapt.
     
    timgr, Mar 30, 2006
    #9
  10. Mar 30, 2006
    linckeil

    linckeil Member

    Danbury CT
    Joined:
    Aug 19, 2004
    Messages:
    492
    Thanks for all the info guys. And 65CJ5, you got a great site. Once I read your heater motor upgrade, I'll be sure to check out your other writeups.
     
    linckeil, Mar 30, 2006
    #10
New Posts