1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

How To Paint A Jeep?

Discussion in 'Early CJ5 and CJ6 Tech' started by tomasinator, Jan 21, 2019.

  1. Jan 21, 2019
    tomasinator

    tomasinator Member

    Redmond, WA
    Joined:
    Aug 26, 2015
    Messages:
    415
    I hope to paint my '68 cj5 project this summer. I'm going to spray it myself in the driveway. My project is someone else's failed dream. The jeep came completely disassembled, down to the last bolt. I had the rusted body parts sandblasted and primed (ITLKSEZ Paint and Body, Inc.). I've cut out and patched all the rusted panels. Now I'm assembling the jeep, fitting all the parts, wiring it, and getting it running. Then I plan to take it apart again and paint all the pieces, inside and out.

    [​IMG]

    Here's the question. For all the brackets and parts that bolt to the body, do you paint them individually or do you mount them and paint them with the body? If I paint them separately, then the mounting bolts don't get painted unless I go through the hassle of painting them individually. If I paint the body parts with the brackets pre-mounted, then there's nothing but primer underneath the brackets, perhaps inviting more rust.

    [​IMG]

    Here's an example -- the hood hinge. What's the jeep way to paint all these parts?
     
  2. Jan 21, 2019
    Twin2

    Twin2 not him 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Virginia Beach, VA
    Joined:
    Apr 28, 2011
    Messages:
    5,407
    paint all pieces off the jeep . as to bolts poke hole in cardboard box and paint heads
     
  3. Jan 21, 2019
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    I expect assembly will chip the bolt heads. I would assemble the body. Then I would paint the Jeep inside and out, like the factory did. The new Jeeps that I've seen did not have paint on the underside - they were e-coat down there. And the paint on the underside of the hood, inside of the fender liners and firewall was much less careful than the exterior paint. It looks like they left the dash off and painted it separately, since the bolts were raw zinc plate (as I recall). If you are using an epoxy primer, it will be plenty weather-proof and durable for any surfaces that don't get painted. BTW when I wrecked my first CJ-6, the dealership painted the new body top and bottom.
     
  4. Jan 21, 2019
    Nebr1957CJ5

    Nebr1957CJ5 I will do it tomorrow

    Lincoln NE
    Joined:
    Nov 2, 2018
    Messages:
    61
    That's what I would recommend as well. With good paint on the hardware, you should be able to install them with minimal touch up if any. I use tons of painted hardware at work. As long as guys installing them don't go crazy with power/air tools the paint will hold
     
  5. Jan 21, 2019
    scott milliner

    scott milliner Master Fabricator

    Seattle Wa.
    Joined:
    Dec 17, 2002
    Messages:
    2,361
    This procedure is for a total disassembled Jeep.

    Painted the bottom of the tub and firewall off the frame. Then mounted the tub to the frame and painted the inside of the tub. Then the sides and top cowl. The fenders and hood can be painted separate.
     
  6. Jan 21, 2019
    Steve's 70-5

    Steve's 70-5 Active Member

    Louisville, Ky
    Joined:
    Nov 12, 2009
    Messages:
    1,381
    I painted everything separate, than put it together. From your post it sound like this will be your first. Paint the under side of the tub first, this will be a good place to start. I painted the under side of my fenders and hood.Then next week end painted the tops of everything. When dpaint the tub, I painted the under side, then mounted the tub and painted the interior. Then I painted the exterior last. Try to paint smaller areas, this worked best for me. When every I try to paint a lot, things would go bad.
     
  7. Jan 21, 2019
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    I say disassemble, BTDT.

    upload_2019-1-21_20-35-23.jpeg
     
    tripilio, J walk and Twin2 like this.
  8. Jan 21, 2019
    mike starck

    mike starck Member

    salem,oregon
    Joined:
    Jun 22, 2006
    Messages:
    762
    Painted in pieces then assembled. I used nylon flat washers under bolts and screws to prevent paint from popping. Tighten slowly then go back and snug down a little at a time.Mask off critical areas when doing assembly. IMG_0087 (1).JPG IMG_0088 (5).JPG chris and jo 002.jpg
     
    tripilio, IRQVET and 62CheepJeep like this.
  9. Jan 21, 2019
    sterlclan

    sterlclan Member 2022 Sponsor

    exploring the...
    Joined:
    Feb 21, 2009
    Messages:
    3,869
    prime the parts, jamb the edges and under the hinges and such with paint, put it together , scuff everything you can see and apply finish.
     
  10. Jan 22, 2019
    Rick Whitson

    Rick Whitson Detroit Area 2024 Sponsor 2022 Sponsor

    I live South of...
    Joined:
    Dec 2, 2014
    Messages:
    1,725
    I use all stainless bolts, nuts and screws with washers, it cost a little more but some day you may want to take it apart again. I found stainless carriage bolts at Lowes for mounting the body to the frame, I had to file the holes square but it is no big deal. Good Luck
     
  11. Jan 22, 2019
    Nebr1957CJ5

    Nebr1957CJ5 I will do it tomorrow

    Lincoln NE
    Joined:
    Nov 2, 2018
    Messages:
    61
    For the visible hardware, did you then paint it or keep the bright finish? It's all personal taste, but I was just curious
     
  12. Jan 22, 2019
    colojeepguy

    colojeepguy Colorado Springs

    At the foot of...
    Joined:
    Apr 4, 2010
    Messages:
    7,110
    I painted mine in pieces and used tape on my wrenches and sockets when putting everything back together.
     
    Twin2 likes this.
  13. Jan 22, 2019
    sterlclan

    sterlclan Member 2022 Sponsor

    exploring the...
    Joined:
    Feb 21, 2009
    Messages:
    3,869
    Stainless bolts aren’t as strong as a graded bolt and they tend to gall threads upon removal if you choose stainless use plenty of never seize or they may never come out again.
     
    IRQVET likes this.
  14. Jan 22, 2019
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    They're fine for body stuff. re. galling I don't know what alloy is prevalent these days but i haven't had a ss fastener gall in years.
     
  15. Jan 22, 2019
    sterlclan

    sterlclan Member 2022 Sponsor

    exploring the...
    Joined:
    Feb 21, 2009
    Messages:
    3,869
    Seems like every stainless bolt I’ve used in the last five years has been junk.
     
  16. Jan 22, 2019
    Howard Eisenhauer

    Howard Eisenhauer Administrator Staff Member

    Tantallon, Nova...
    Joined:
    Nov 22, 2003
    Messages:
    8,102
    Where are you getting them at? Mine are a combo from a the ubiquitous ss dress up kit & ones I bought at a fastener supply place. I do know what you're talking about, many years ago the first time I fixed up Tonk I had a terrible time with ss, all sorts of jamming & breaking but not this time, no issues at all. :whistle:
     
  17. Jan 22, 2019
    sterlclan

    sterlclan Member 2022 Sponsor

    exploring the...
    Joined:
    Feb 21, 2009
    Messages:
    3,869
    I don’t source them use what the customer brings or at my “real” job the boss gets them somewhere cheap.
     
  18. Jan 22, 2019
    timgr

    timgr We stand on the shoulders of giants. 2022 Sponsor

    Medford Mass USA
    Joined:
    Aug 10, 2003
    Messages:
    23,596
    What do you mean by "jamb" here?
     
  19. Jan 22, 2019
    tomasinator

    tomasinator Member

    Redmond, WA
    Joined:
    Aug 26, 2015
    Messages:
    415
    Did you make a paint booth out of a Harbor Freight portable garage frame? That looks really good.
     
  20. Jan 22, 2019
    sterlclan

    sterlclan Member 2022 Sponsor

    exploring the...
    Joined:
    Feb 21, 2009
    Messages:
    3,869
    I finish prime and while the recoat window is still open I do the insides and all edges and any hinge spots basically anything covered by something else will get paint on it assemble the whole thing finish sand and apply finish. I like to spray everything in the orientation that it will eventually live.
     
    Last edited: Jan 22, 2019
New Posts