1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Sea Foam And The V6 Dauntless

Discussion in 'Early CJ5 and CJ6 Tech' started by Donnie, Apr 27, 2019.

  1. Apr 27, 2019
    Donnie

    Donnie Member

    saskatoon,canada
    Joined:
    Jan 22, 2019
    Messages:
    99
    i wanna run a can of seafoam through the vacuum, can i use the line that unplugs from the distributor.
    cheers
     
    Donnie, Apr 27, 2019
    #1
  2. Apr 27, 2019
    Admiral Cray

    Admiral Cray I want to do this again.. Staff Member

    Bainbridge...
    Joined:
    Sep 21, 2009
    Messages:
    204,352
    Do it slowly...

    Don't want to hammer lock a cylinder...
     
    Admiral Cray, Apr 27, 2019
    #2
  3. Apr 27, 2019
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,376
    Why not just put it in the gas?
     
    Glenn, Apr 27, 2019
    #3
  4. Apr 27, 2019
    Donnie

    Donnie Member

    saskatoon,canada
    Joined:
    Jan 22, 2019
    Messages:
    99
    so i leave the engine running and use about a half bottle through the vacuum, how do i do it slowly, add a little bit at a time, let it run add a little more
     
    Donnie, Apr 27, 2019
    #4
  5. Apr 27, 2019
    Donnie

    Donnie Member

    saskatoon,canada
    Joined:
    Jan 22, 2019
    Messages:
    99
    I heard it works better through the vacuum. But Iam no machanic
     
    Donnie, Apr 27, 2019
    #5
  6. Apr 27, 2019
    Chilly

    Chilly Active Member

    Joined:
    Mar 12, 2007
    Messages:
    1,486
    Get engine good and hot, use a very skinny straw to slurp it in. Have someone in the drivers seat to shut it off while its drinking. Idea is to leave cylinders hot and wet with the stuff. This is the sea foam made for puttting into intake? Or regular stuff? Might be same except for packaging, i wouldnt know.
     
    Chilly, Apr 27, 2019
    #6
  7. Apr 27, 2019
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,376
    Seems like putting it in through the carb would be the same thing.
     
    Glenn, Apr 27, 2019
    #7
  8. Apr 27, 2019
    Mcruff

    Mcruff Earlycj5 Machinist

    Albertville, AL
    Joined:
    Sep 22, 2002
    Messages:
    5,349
    I’ve always just trickled it down the carb. Same way you used to do water or auto transmission oil to clean chambers. Keep the rpm up around 2000-2500rpm.
     
    Mcruff, Apr 27, 2019
    #8
  9. Apr 27, 2019
    Glenn

    Glenn Kinda grumpy old man Staff Member

    Apopka, Fl
    Joined:
    Sep 21, 2002
    Messages:
    12,376
    Yep, through the carb is vacuum too. It's all I've done or seen done.
     
    Glenn, Apr 27, 2019
    #9
  10. Apr 28, 2019
    Admiral Cray

    Admiral Cray I want to do this again.. Staff Member

    Bainbridge...
    Joined:
    Sep 21, 2009
    Messages:
    204,352
    I use to use a top end cleaner from GM on my Blazer. It was recommend by the factory manual. I poured it down the carb slowly at first and the engine would stall. pour the remaining half in and let it set for 30 minutes or so. Start the engine and it smoked like crazy. I think is was for carbon build up. I always worried about hammer lock, but it never happened. I still worry...

    GM Top Engine Cleaner Vintage Sealed Engine Performance 16 oz Classic Can | eBay
     
    Admiral Cray, Apr 28, 2019
    #10
New Posts