1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Recent Content by HerkEng

  1. HerkEng
    Post

    V6 emblem differences

    Irish pride edition? St Patrick's day special?
    Post by: HerkEng, Aug 23, 2023 in forum: Early Jeep Restoration and Research
  2. HerkEng
    Post

    My New To Me South Bend

    Chain saw bar oil makes a pretty good way oil. Cutting oils are easy to find locally, the brown Oatey stuff in the plumbing aisle at local home...
    Post by: HerkEng, Feb 16, 2018 in forum: The Tool Shed
  3. HerkEng
    Post

    My New To Me South Bend

    Here's a few rabbit holes: SOUTH BEND LATHE WORKS South Bend Lathe Works - Publication Reprints | VintageMachinery.org The SBL Workshop
    Post by: HerkEng, Nov 2, 2017 in forum: The Tool Shed
  4. HerkEng
    Post

    Early Cj5 Correct Ignition Switch And Keys 1950s

    Assuming it is similar with CJ's and Wagons/Trucks. The concave "STARTER" bezel was typical of 12 volt 57-60, and was a 4-position switch. Mid...
    Post by: HerkEng, Oct 24, 2017 in forum: Early Jeep Restoration and Research
  5. HerkEng
    Post

    Most Simple Engine Swap To Fuel Injected V6

    An L-67 supercharged 3800 would seem the ideal swap. Only obstacles being the throttle body location and it uses the "metric" bell housing.
    Post by: HerkEng, Sep 14, 2017 in forum: Early CJ5 and CJ6 Tech
  6. HerkEng
    Post

    Factory Vacuum Wiper Blade

    Might look into air cooled VW blades. Impress your friends and say they're for a Triumph TR-3.
    Post by: HerkEng, Jun 1, 2017 in forum: Early CJ5 and CJ6 Tech
  7. HerkEng
    Post

    Blueprint 225

    The later 231 pickups were larger, like 5/8". If it will fit it is a great upgrade, especially if you've taken the time to enlarge the passages...
    Post by: HerkEng, Mar 11, 2016 in forum: Builds and Fabricators Forum
  8. HerkEng
    Post

    Stubborn hub Dana 44 tapered shaft

    Best is to buy/rent one of these http://www.amazon.com/OTC-7394-Universal-Hub-Puller/dp/B0002SRH60
    Post by: HerkEng, Nov 16, 2015 in forum: Early CJ5 and CJ6 Tech
  9. HerkEng
    Post

    11" brakes on Willys Pickup Truck

    So the trucks all had 11" brakes to begin with (manual adjustment). Later self adjusting backing plates could be a worthwhile upgrade I suppose....
    Post by: HerkEng, Nov 9, 2015 in forum: Early Jeep Restoration and Research
  10. HerkEng
    Post

    Megasquirt Build

    Re: TBI thoughts! I've got less than $200 in my whole setup so far, that includes a TB, ECM, 2 harnesses, 2 HEI distributors (so I can build a...
    Post by: HerkEng, Sep 28, 2015 in forum: Builds and Fabricators Forum
  11. HerkEng
    Post

    Megasquirt Build

    Re: TBI thoughts! Not knocking the MS but why not just use a modded GM 1227747 ECM? I'm doing a similar swap into my Buick 350 J-truck using all...
    Post by: HerkEng, Sep 28, 2015 in forum: Builds and Fabricators Forum
New Posts