1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

Focker's '71 CJ5 Drivable Build

Discussion in 'Builds and Fabricators Forum' started by Focker, Aug 19, 2014.

  1. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    That looks great!
     
  2. GeoffreyL

    GeoffreyL Well-Known Member

    Those Ross mounts for the bell crank are welded on from the factory. A little excessive if you ask me, welded and riveted, I took on off once, took forever.
     
    Hellion likes this.
  3. 55_Willys_CJ5

    55_Willys_CJ5 Nephews Visit 2017 2024 Sponsor 2023 Sponsor

    X3. Way to go Focker
     
  4. Focker

    Focker That's a terrible idea...What time? Staff Member

    Thanks gang! (y)
     
  5. Focker

    Focker That's a terrible idea...What time? Staff Member

    Yeah...I read that in another post the other day. :oops:

    You're not kidding...Took forever.
     
  6. nickmil

    nickmil In mothballs.

    Cutoff wheel to cut through the welds and cut the heads off the rivets. Air hammer to drive out what's left of the rivets. Still a pain but makes it much easier.
     
  7. Focker

    Focker That's a terrible idea...What time? Staff Member

    That's how I did it...I'm glad the engine was out of the way. (y)
     
  8. txtoller

    txtoller Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Yep, those bell cranks are a beast to get off!

    Focker, can you please show me how your mirror is attached? I prefer the small round mirrors.

    Looking good!
     
  9. Focker

    Focker That's a terrible idea...What time? Staff Member

    Don't laugh but it's a mirror from a Yamaha scooter. I drilled and tapped the door channel. You can just notice it here in this post (first picture).

    Focker's '71 CJ5 Drivable Build
     
  10. txtoller

    txtoller Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    I like that set up!

    Thank you
     
  11. Focker

    Focker That's a terrible idea...What time? Staff Member

  12. 47v6

    47v6 junk wrecker! 2023 Sponsor 2022 Sponsor

    Wow, looks great. Don't forget to hook up the PCV.
     
    heavychevy likes this.
  13. homersdog

    homersdog Tulsa, Ok 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Huge improvement! Excellent work!
     
  14. Focker

    Focker That's a terrible idea...What time? Staff Member

    Fired right up after the fuel pump got some gas to the carb with only a few cranks. (y)

    [​IMG]

    [​IMG]
     
    IRQVET, Beach66Bum and Danefraz like this.
  15. Focker

    Focker That's a terrible idea...What time? Staff Member

    I love being a neat freak. When I finish a project...The garage is back in order too. I put my tools away as I finish, by the time I'm down to the final step there's only a tool or 2 to put away. :)

    [​IMG]
     
    tripilio likes this.
  16. 55_Willys_CJ5

    55_Willys_CJ5 Nephews Visit 2017 2024 Sponsor 2023 Sponsor

    All you hardwork has paid off. Your engine compartment looks awesome. (y):D
     
  17. Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Now it's time to get it dirty!!
     
  18. Focker

    Focker That's a terrible idea...What time? Staff Member

    Simple battery hold down bar...Really just a chance to use my little milling vise so I can feel like Tarry and Chris. :rolleyes:

    [​IMG]

    [​IMG]

    [​IMG]

    [​IMG]
     
  19. 47v6

    47v6 junk wrecker! 2023 Sponsor 2022 Sponsor

    looks great. please don't feel like me. It would cause permanent insanity.
     
    Cowboyjeeper likes this.
  20. Focker

    Focker That's a terrible idea...What time? Staff Member

    Sorry...Just a fan/borderline stalker. :ninja: