1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

1962 CJ5 Michaels Project

Discussion in 'Builds and Fabricators Forum' started by chris423, Jan 27, 2015.

  1. Aug 24, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    test fit[​IMG]
     
  2. Aug 24, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    test fit[​IMG]
     
  3. Aug 24, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    just primed top of bed[​IMG]
     
  4. Aug 24, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    air compressor and I have been trimming out a house more this week
     
  5. Aug 24, 2015
    uncamonkey

    uncamonkey Member

    Greeley CO
    Joined:
    Jun 2, 2009
    Messages:
    2,104
    Just saying I used to have a 110V flux core machine, It was stolen so I got a 220V with shield gas. Much better welds and the ability to do some heavier metal. A friend does jobs like power plants and refinerys. At the end of the job they sell all of the equipment. If only I had the $.
     
  6. Sep 7, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    I have to catch this up sept1 the tub was removed from the frame . it sat on the roll bar and sawhorses while I plug welded the rear floor in. now it sits on the passenger side so I can weld all I can get to . the a supports in the front by the engine and master cylinder are history working on some 2inch angle for replacement so far so good . the frame was pressure washed . I paid special attention to where I have heard of cracks so far so good on that no cracks but the fame was boxed in all around the engine Is this stock????
     
  7. Sep 25, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    [​IMG][​IMG]old and new
     
  8. Sep 25, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
  9. Sep 25, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    old passenger side [​IMG]
     
  10. Sep 25, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    This will be a driver. I am doing my best not to BUBBA engineer, after all this is a first for me and my son ! Oh thanks to Ron in Va I have a complete E-brake !!!!
     
  11. Sep 26, 2015
    rejeep

    rejeep Well-Known Member 2024 Sponsor 2023 Sponsor 2022 Sponsor

    Rochester, NY
    Joined:
    Nov 5, 2009
    Messages:
    1,691
    for my time I am very happy with the aqualu tub...
    but you are doing a great job with lots of patience repairing that tub :beer:
     
  12. Sep 29, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    Thanks It has taken some patience with the tub . The rust is never ending ! Yesterday I got the bottom primed . And now the rain has started . We will see how it will hold up . !!!
     
  13. Oct 1, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    What to do in the rain [​IMG]tailgate repair the usual rusted out bottom by the hinge slots [​IMG]when done it wont look new but neither will the rest !!!
     
  14. Oct 1, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    [​IMG]still not complete ! but a lot better than bondo over the rust hole
     
  15. Oct 1, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    painted and cleaned up the e brake drum and backing plate[​IMG][​IMG]
     
  16. Oct 27, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    just n update started bed ling the bottom and then the went the temps above 68* so I have been messing with engine compartment also the heater unit pics to come . the fan motor works and is 12v
     
  17. Nov 5, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    why my heater wont work
     
  18. Nov 5, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    the bottom
     
  19. Nov 5, 2015
    sterlclan

    sterlclan Member 2024 Sponsor 2022 Sponsor

    exploring the...
    Joined:
    Feb 21, 2009
    Messages:
    3,888
    You do not have permission to view media within this album.
     
  20. Nov 6, 2015
    chris423

    chris423 Sponsor

    greeneville tn
    Joined:
    Dec 30, 2014
    Messages:
    565
    can you see the pictures? I change privacy settings on album.
     
New Posts