1. Registration trouble? Please use the "Contact Us" link at the bottom right corner of the page and your issue will be resolved.
    Dismiss Notice

where would you go to find engine parts for a 225?

Discussion in 'Early CJ5 and CJ6 Tech' started by hansom, Jun 3, 2009.

Page 1 of 2
  1. Jun 3, 2009
    hansom

    hansom New Member

    Joined:
    Mar 31, 2009
    Messages:
    15
    I need to find some headers for my dauntless 225 v6, and I can't find a durn thing. If this goes on, I'll just have to try my hand at crafting some
     
    hansom, Jun 3, 2009
    #1
  2. Jun 3, 2009
    EricM

    EricM Active Member

    Southern California
    Joined:
    Dec 19, 2007
    Messages:
    1,019
    EricM, Jun 3, 2009
    #2
  3. Jun 3, 2009
    Rozcoking23

    Rozcoking23 RUN & GET BIT! 2024 Sponsor

    Stockton, CA
    Joined:
    Mar 29, 2008
    Messages:
    1,075
    J.C.W. carries headers for the 225 also
     
    Rozcoking23, Jun 3, 2009
    #3
  4. Jun 3, 2009
    Hurstjeepster

    Hurstjeepster New Member

    Helena, Montana
    Joined:
    May 24, 2007
    Messages:
    19
    Hurstjeepster, Jun 3, 2009
    #4
  5. Jun 3, 2009
    mike starck

    mike starck Member

    salem,oregon
    Joined:
    Jun 22, 2006
    Messages:
    762
    Hedman Headers still makes the fenderwell header.i have a set on my jeep.got them from summit racing.i can find part number if you want it.

    mike s.
     
    mike starck, Jun 3, 2009
    #5
  6. Jun 3, 2009
    captain cj

    captain cj Member

    Crystal Beach...
    Joined:
    Sep 27, 2005
    Messages:
    331
    Headers aren't hard to find at all, I have Hedmans on mine ,very happy with them.
     
    captain cj, Jun 3, 2009
    #6
  7. Jun 3, 2009
    Chris Insull

    Chris Insull All roads lead me back to the beach... 2023 Sponsor 2022 Sponsor

    Chesapeake, VA.
    Joined:
    Sep 22, 2002
    Messages:
    806
    I've been running Advance Adapters headers since June '98. Nice, thick flanges, haven't had a leak yet and no burn thru. Yes, they are more expensive than some; but worth it IMHO!!
     
    Chris Insull, Jun 3, 2009
    #7
  8. Jun 3, 2009
    boinky

    boinky New Member

    Statesboro
    Joined:
    Apr 1, 2009
    Messages:
    24
    boinky, Jun 3, 2009
    #8
  9. Jun 3, 2009
    Patrick

    Patrick Super Moderator Staff Member

    Los Alamos, NM
    Joined:
    Sep 22, 2002
    Messages:
    8,360
    Summit has Hedmans. FWIW, the Hedmans on my Jeep outlasted (they're still good) the Advance Adapters headers my Dad had. His rusted out where the 3 pipes come together. He's got Hedmans now.
     
    Patrick, Jun 3, 2009
    #9
  10. Jun 3, 2009
    lynn

    lynn Time machine / Early CJ5 HR Rep Staff Member

    Huntingdon PA
    Joined:
    Sep 20, 2002
    Messages:
    3,437
    Be sure to discuss the application when you order headers from Novak. I discussed it with them...IIRC, the Sanderson's will interfere with one stock motor mount location on stock set ups. They're designed for swaps, not stock set ups. (... that's how I remember it but I could be wrong... Talk to Eric at Novak.)


    I also recommend using Header Buddys at the collector, instead of the flange and gaskets that always leak:
    http://www.headerbuddy.com/cgi-bin/...h=23;search=HEADER BUDDY;limit=category;v=2.0

    HTH
     
    lynn, Jun 3, 2009
    #10
  11. Jun 3, 2009
    FugginJim

    FugginJim In control Sometimes

    Pinon Hills,...
    Joined:
    Nov 22, 2004
    Messages:
    379
    I purchased hedman headers they were belled at the collector no gaskets needed been running only a short time but Im very satisfied so far. It did take a long time to get them when I ordered them not an off the shelf item.
     
    FugginJim, Jun 3, 2009
    #11
  12. Jun 3, 2009
    jpflat2a

    jpflat2a what's that noise?

    Hermosa, SD
    Joined:
    Jul 30, 2003
    Messages:
    8,563
    x2
    mine have been on the Jeep since 1983
     
    jpflat2a, Jun 3, 2009
    #12
  13. Jun 3, 2009
    Mcruff

    Mcruff Earlycj5 Machinist

    Albertville, AL
    Joined:
    Sep 22, 2002
    Messages:
    5,350
    My Hedmans have been on since April of 1992. No rust thru or leaks.
     
    Mcruff, Jun 3, 2009
    #13
  14. Jun 3, 2009
    Warloch

    Warloch Did you say Flattie??? Staff Member

    Falcon, CO
    Joined:
    Mar 4, 2003
    Messages:
    5,507
    I have used the AA ones - and have a new set on the shelf.

    Right now I am working with Eric at Novak to redesign the Headers to be more swap friendly - the stock ones they have (I have some in the shop now) work with the stock motor mounts. We are tweeking them to work with Stock and conversion setups.

    They are made by Sanderson - got a plate right on them.
     
    Warloch, Jun 3, 2009
    #14
  15. Jun 3, 2009
    Daryl

    Daryl Sponsor

    Bonney Lake, WA
    Joined:
    May 25, 2006
    Messages:
    2,907
    Flanges on the AA are by far the best at sealing and holding gaskets-3/8" thick. The tubes give out long before the hedmans however. I have had several sets of AA and have never had to change a gasket on one due to failure.
     
    Daryl, Jun 3, 2009
    #15
  16. Jun 3, 2009
    lynn

    lynn Time machine / Early CJ5 HR Rep Staff Member

    Huntingdon PA
    Joined:
    Sep 20, 2002
    Messages:
    3,437
    I knew there was a redesign of the Sandersons in the works... I guess I didn't remember the details well enough :rofl:
    Kind of like a camera memory card... once you exceed capacity, some things just drop out to make room for other stuff ;) :D
     
    lynn, Jun 3, 2009
    #16
  17. Jun 3, 2009
    Warloch

    Warloch Did you say Flattie??? Staff Member

    Falcon, CO
    Joined:
    Mar 4, 2003
    Messages:
    5,507
    Yup - know what you mean, I had a digi card swap done... Didn't help.

    Maybe I should stop drinking and save those brain cells?

    Nah - life is too stressful to stop drinking. Got to do my part and recycle, may as well start with the brain cells :)
     
    Warloch, Jun 3, 2009
    #17
  18. Jul 27, 2009
    Warloch

    Warloch Did you say Flattie??? Staff Member

    Falcon, CO
    Joined:
    Mar 4, 2003
    Messages:
    5,507
    Just an update for those interested in the Novak Sanderson Headers - got the Pass Side Header today that fixes all the fit issues. We may still shorten the Drv Side when we can get it pushed through Sanderson to have the flange at the top of the frame.

    Got pics on My Site
     
    Warloch, Jul 27, 2009
    #18
  19. Jul 29, 2009
    Big Bear

    Big Bear New Member

    New England
    Joined:
    Sep 10, 2006
    Messages:
    20
    Got headman headers P/n: 69420 from georges jeep parts
    (601)542-0013
    [​IMG]

    [​IMG]
     
    Big Bear, Jul 29, 2009
    #19
  20. Jul 29, 2009
    nickmil

    nickmil In mothballs.

    Happy Valley, OR
    Joined:
    Sep 23, 2002
    Messages:
    12,633
    Those look awesome! I notice in the pics the motor mounts off the frame are not stock. Are these going to be engineered to clear the stock motor mounts?
     
    nickmil, Jul 29, 2009
    #20
Page 1 of 2
New Posts